F3001o:p>

 

10Gbps SFP+(Small Form-factor Pluggable) Active Optical Cable (AOC), Short Wavelength(850nm) Up to st1:chmetcnv TCSC="0" NumberType="1" Negative="False" HasSpace="False" SourceValue="100" UnitName="m" w:st="on">100m Reach

                                                                                              

F3001 Overview

 Fiberers F3001 10Gb/s Active Optical Cable (AOC) Assembly for SFP+ Applications is designed for 10 Gbps Ethernet equipment, providing high-speed transmission up to 100 meters of multimode fiber and enabling high port density and ease of handling of similar copper cables. The AOC transmits a single channel operating up to 10.3125 Gbps, using industry leading VCSEL technology and an advanced new light-engine design.

  

Product Features - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

 

Data-rate of 10.3125Gbps operation

850nm VCSEL laser and PIN photodetector

Supports Fiber Channel Physical Interface C 5 (FC-PI-5) Specification

Supports SFF-8431 Specifications for Enhanced Small Form Factor Pluggable Module SFP+

Fiber link up to 100 meters on 2000MHz/km MMF

+3.3V single power supply and Hot Pluggable

Operating case temperature: 0 to +70C

Full set of diagnostic features

Low power consumption

Bend insensitive fiber

 lications

 

10 Gigabit Ethernet (10GbE)

Cost effective 10G SFP+ link solution

High Performance Computing clusters

System Internal data link solution

System cascade applications

Proprietary Interconnects

 Standard

    Mechanical specifications compliant with SFF-8432

Electrical specifications compliant with SFF-8431

RoHS Compliant

 Description - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

Fiberers F3001 high speed SFP+ AOC (Active Optical Cable) assemblies use active circuits to support longer distances than standard passive or Active SFP+ Copper Cables. They are designed for high speed, short range data link via optical fiber wire. SFP+ AOC cables provide high performance Enhanced Small Form Factor Pluggable (SFP+) interface and is a cost effective solution for Data Center/ storage and all short range data application.

SFP+ Connectors meet the harshest external operating conditions including temperature, humidity and EMI interference. Final test and quality systems assure high quality cable assemblies conforming to the high-speed electrical performance requirements in industry specifications.

SFP+ AOC modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget.

 Overview of Product - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

Parameter	Value	Comments
Number of data lanes	1 VCSEL Transmitter and 1 Receiver per module
Data rate per channel	Up to 10.3125 Gbps
Electrical interface and pin-out	20-pin edge connector
Pin description	Per SFF-8431 rev4.1
Management interface	I2C, serial, timing per SFF-8472
Length of AOC	1 to 100	Meters, using Advance OM2+ MM fiber
BER	<10-12	Tested with PRB 231-1 test pattern
Power supply	3.3 VDC

 Absolute Maximum Ratings 

Parameter	Symbol	Min	Max	Unit
Maximum Supply Voltage	Vcc	0	3.6	V
Storage Temperature	Ts	0	70	C
Transmitter single-ended input voltage	mVpp		1400	mV
Relative Humidity	RH	5	95	%

 Recommended Operating Conditions - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

 

Parameter	Symbol	Min	Typical	Max	Unit
Operating Case Temperature	Standard Tc	0	25	70	C
Power Supply Voltage	Vcc	3.13	3.3	3.47	V
Power Supply Current	Icc			260	mA
Power Consumption			600	800	mW
Power Supply Noise Tolerance	mVpp			200	mV

 Active Cable Transmitter Optical and Electrical Characteristics per Lane

 

Parameter		Symbol	Min	Typical	Max	Unit
Centre Wavelength		c	840	850	860	nm
Spectral Width (RMS)					0.45	nm
Average Output Power		Pout	-6.5		-1	dBm
Extinction Ratio		ER	3.5			dB
Transmitter Dispersion Penalty		TDP			3.9	dB
Relative Intensity Noise		Rin			-128(12dB reflection)	dB/Hz
Optical Return Loss Tolerance					12	dB
Optical Rise/Fall Time (20%~80%)		tr/tf	0.03			ns
Data Input Swing Differential		VIN	90		350	mV
C common mode voltage tolerance			15			mV
Data Dependent Input Jitter		DDJ			0.1	UI
Data Input Total Jitter		TJ			0.28	UI
Input Differential Impedance		ZIN	90	100	110
Transmit Disable Input	High	VIH	2.0		Vcc+0.3	V
	Low	VIL	0		0.8	V
Transmit Enable Output	High	VOH	2.4		Vcc+0.3	V
	Low	VOL	0		0.4	V

Active Cable Receiver Optical and Electrical Characteristics per Lane

 

Parameter		Symbol	Min	Typical	Max	Unit
Centre Wavelength		c	840	850	860	nm
Receiver Sensitivity		Psens			-11	dBm
Receiver Overload		Pin			-1.0	dBm
LOS De-Assert		LOSD			-11	dBm
LOS Assert		LOSA	-30			dBm
LOS Hysteresis			0.5		4	dB
Stressed Sensitivity in OMA					-7.5	dBm
Receiver Reflectance					-12	dB
Data Output Swing Differential		Vout	300		850	mV
Output Differential Impedance		Zon	90	100	110
LOS Output	High	VOH	2.4		Vcc+0.3	V
	Low	VOL	0		0.4	V

 

Diagnostics Specification - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

 

Parameter	Range	Unit	Accuracy	Calibration
Temperature	0 to 70		3	Internal / External
Voltage	3.0 to 3.6	V	3%	Internal / External
Bias Current	0 to 100	mA	10%	Internal / External
TX Power	-6.5 to -1	dBm	3dB	Internal / External
RX Power	-18 to 0	dBm	3dB	Internal / External

 

Pin Definitions - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

 

PIN	Symbol	Description	Remarks
1	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground
2	Tx_Fault	Transmitter Fault. Not supported
3	Tx_Disable	Transmitter Disable. Laser output disable on high or open	Disabled: TDIS>2V or open Enabled: TDIS<0.8V
4	SDA	2-wire Serial Interface Data Line	Should Be pulled up with 4.7k C 10k ohm on host board to a voltage between 2V and 3.6V
5	SCL	2-wire Serial Interface Clock Line
6	MOD_ABS	Module Absent. Grounded within the module.
7	RS0	No connection required
8	RX_LOS	Loss of Signal indication. Logic 0 indicates normal operation	LOS is open collector output
9	RS1	No connection required
10	VEER	Receiver ground (common with transmitter ground)	Circuit ground is isolated from chassis ground
11	VEER	Receiver ground (common with transmitter ground)
12	RDC	Receiver Inverted DATA out. AC coupled
13	RD+	Receiver Non-inverted DATA out. AC coupled
14	VEER	Receiver ground (common with transmitter ground)	Circuit ground is isolated from chassis ground
15	VCCR	Receiver power supply
16	VCCT	Transmitter power supply
17	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground
18	TD+	Transmitter Non-Inverted DATA in. AC coupled
19	TDC	Transmitter Inverted DATA in. AC coupled
20	VEET	Transmitter ground (common with receiver ground)	Circuit ground is isolated from chassis ground

 

Mechanical Characteristics

Parameter	Min	Typ	Max	Unit
Cable Installation Tension			98	N
Cable Operating Tension			31	N
Operating Cable Bend Radius	3			cm

 Pin Diagram - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

v:shapetype id=_x0000_t75 coordsize="21600,21600" o:spt="75" o:preferrelative="t" path="m@4@5l@4@11@9@11@9@5xe" filled="f" stroked="f">

Diagram of Host Board Connector Block Pin Numbers and Names

 

SFP Module EEPROM Information and Management

 

The SFP+ modules implement the 2-wire serial communication protocol as defined in the SFP -8472.The serial ID information of the SFP+ modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information(A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions,, please refer to the SFF-8472, Digital Diagnostic Monitoring Interface for Optical Transceivers.

  

Digital Diagnostic Memory Map (Specific Data Field Descriptions)

 

 

Data Address	Field Size (Bytes)	Name of field	Description of field
BASE ID FIELDS
0	1	Identifier	Type of serial transceiver (03h=SFP)
1	1	Ext. Identifier	Extended identifier of type of serial transceiver(04h)
2	1	Connector	Code for connector type (07=LC)
3-10	8	Transceiver	Code for electronic compatibility or optical compatibility
11	1	Encoding	Code for serial encoding algorithm ( 64B/66B (06h))
12	1	BR, Nominal	Nominal bit rate, units of 100 MBits/sec(67h)
13	1	Reserved	(0000h)
14	1	Length(9um) - km	Link length supported for 9/125 um fiber, units of km
15	1	Length (um)	Link length supported for 9/125 um fiber, units of 100 m
16	1	Length (50um)	Link length supported for 50/125 um fiber, units of 10 m
17	1	Length (62.5um)	Link length supported for 62.5/125 um fiber, units of 10 m
18	1	Length (Copper)	Link length supported for copper, units of meters
19	1	Reserved
20-35	16	Vendor name	SFP transceiver vendor name (ASCII)
36	1	Reserved
37-39	3	Vendor OUI	SFP transceiver vendor IEEE company ID
40-55	16	Vendor PN	Part number provided by SFP transceiver vendor (ASCII)
56-59	4	Vendor rev	Revision level for part number provided by vendor (ASCII)
60-62	3	Reserved
63	1	CC_BASE	Check code , for Base ID Fields (addresses 0 to 62)
EXTENDED ID FIELDS
64-65	2	Options	Indicates which optional SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported)
66	1	BR, max	Upper bit rate margin, units of %
67	1	BR, min	Lower bit rate margin, units of %
68-83	16	Vendor SN	Serial number provided by vendor (ASCII)
84-91	8	Date code	Vendors manufacturing date code
92-94	3	Reserved
95	1	CC_EXT	Check code for the Extended ID Fields (addresses 64 to 94)
VENDOR SPECIFIC ID FIELDS
96-127	32	Read-only	Vendor specific data, read only
128-511	384	Reserved
512-n			Vendor specific

 

EEPROM Serial ID Memory Contents (A0h)

 

Mechanical Dimensions - 10Gbps SFP+ Active Optical Cable 850nm(AOC)

Diagram of Mechanical Dimensions

 

Ordering Information -10Gbps SFP+ Active Optical Cable 850nm(AOC)

 

Note:Custom cables are available in various lengths and other options.

 

Important Notice